1297 lines
53 KiB
Plaintext
1297 lines
53 KiB
Plaintext
#txt
|
|
# -----------------------------------------------------------------------------
|
|
# Example Profile for Cisco ATA (SCCP) 3.2.4 Release
|
|
# -----------------------------------------------------------------------------
|
|
# IMPORTANT: File must begin with "#txt" (without the quotes) for the
|
|
# formatting tool (cfgfmt.exe) to treat it as a text file.
|
|
#
|
|
# NOTE: 1. A hash (#) at the beginning of the line is a comment. The
|
|
# formatting tool ignores any line beginning with the token.
|
|
#
|
|
# 2. All parameter/value pairs are OPTIONAL; however, they may be
|
|
# needed nevertheless for the Cisco ATA to function properly
|
|
# if no prior value had been programmed.
|
|
#
|
|
# 3. If IVR access code is available, either the alphanumeric or
|
|
# numeric entry method may be used to specify the parameter value.
|
|
# A hexadecimal parameter value must be entered as a decimal value
|
|
# when the IVR is used.
|
|
#
|
|
# 4. Parameter values can be one of the following:
|
|
#
|
|
# a. Alphanumeric string
|
|
# Ex: SIP-4-Ever$#, 1234, #012-34la$!-
|
|
#
|
|
# b. Numeric digit string
|
|
# Ex: 593, 960135, 19690489
|
|
#
|
|
# c. Array of comma-separated short integer
|
|
# Ex: {395,65534,20,32768,105} (without brackets)
|
|
#
|
|
# d. IP address
|
|
# Ex: 192.168.2.170, 64.15.243.3
|
|
#
|
|
# e. Extended IP address -- IP address with Port
|
|
# Ex: 192.168.2.170.9001, 174.10.232.53.10364
|
|
#
|
|
# f. Boolean
|
|
# Ex: 0 or 1
|
|
#
|
|
# g. Bitmap value -- unsigned hex integer (32-bit)
|
|
# Ex: 0x00060400, 0x125f0431
|
|
#
|
|
# h. Integer (32-bit)
|
|
# Ex: 2147483647, 56, 65342
|
|
#
|
|
# 5. Factory defaults are marked with an asterisk '*'
|
|
#
|
|
# 6. "RESERVED" bits should be set to '0'.
|
|
#
|
|
# -----------------------------------------------------------------------------
|
|
|
|
# ============================= Security Parameter ============================
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: UIPassword
|
|
# Access Code: 7387277
|
|
# Value Type: Alphanumeric string (9 characters max)
|
|
#
|
|
# Description: Control access to the web page and IVR interface. If set to
|
|
# a non-zero value, then every new web session will be prompted
|
|
# for the password. The ATA will also prompt with P-A-S-S-W-D
|
|
# when attempting to modify a protected configuration parameter
|
|
# via the IVR.
|
|
#
|
|
# Default: 0 = Password is disabled.
|
|
|
|
UIPassword:0
|
|
|
|
# ========================== Provisioning Parameters ==========================
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: UseTftp
|
|
# Access Code: 305
|
|
# Value Type: Boolean
|
|
#
|
|
# Description: Indicate whether a TFTP server should be contacted for
|
|
# provisioning the ATA
|
|
#
|
|
# Options: *1 = Use TFTP server for provisioning
|
|
# 0 = Do not use TFTP server for provisioning
|
|
|
|
UseTftp:1
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: TftpURL
|
|
# Access Code: 905
|
|
# Value Type: Alphanumeric string (31 characters max)
|
|
#
|
|
# Description: IP address or URL of TFTP server to use.
|
|
#
|
|
# This value is required if the DHCP server will not provide
|
|
# the TFTP address. You can optionally include the path prefix
|
|
# to the TFTP file to download. Example: If the TFTP server IP
|
|
# address is 192.168.2.170 or wwww.cisco.com, and the path to
|
|
# download the ATA profile is in /ata186, then you can
|
|
# specify the URL as 192.168.2.170/ata186 or
|
|
# www.cisco.com/ata186.
|
|
#
|
|
# Note: From the IVR interface, you can only enter the IP address.
|
|
# From the web server interface, you can enter the actual URL.
|
|
#
|
|
# Default: 0 = Use DHCP-provided TFTL URL, if "UseDhcp" parameter is
|
|
# enabled. If DHCP does not provide a TFTP URL, then the
|
|
# ATA can not be provisioned automatically and it must be
|
|
# manually provisioned.
|
|
|
|
TftpURL:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: AltTftpURL
|
|
# Access Code: 935
|
|
# Value Type: Alphanumeric string (31 characters max)
|
|
#
|
|
# Description: Alternate IP address or URL of TFTP server to use in
|
|
# Call Manager Environment.
|
|
#
|
|
# Note: From the IVR interface, you can only enter the IP address.
|
|
# From the web server interface, you can enter the actual URL.
|
|
#
|
|
# Default: 0 = Use DHCP-provided Alternate TFTL URL (provided in
|
|
# the second value of option 150, if exists).
|
|
|
|
AltTftpURL:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: CfgInterval (Not used for SCCP)
|
|
# Access Code: 80002
|
|
# Value Type: Integer (60 - 4294967295 seconds)
|
|
#
|
|
# Description: Interval between each configuration update.
|
|
#
|
|
# When TFTP is used for provisioning, at every such interval
|
|
# expiration, the box will perform a TFTP GET of its
|
|
# configuration file at the earliest possible time -- when the
|
|
# box is idle. CfgInterval can be set to some random value to
|
|
# achieve random contact interval from individual ATA box to the
|
|
# TFTP server.
|
|
#
|
|
# Default: 3600 seconds
|
|
|
|
CfgInterval:3600
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: EncryptKey
|
|
# Access Code: 320
|
|
# Value Type: Hexadecimal character string (8 Hex characters maximum)
|
|
#
|
|
# Description: Key that ATA will use to decrypt its configuration profile
|
|
#
|
|
# Options: *0 = no encryption was made on the incoming profile from
|
|
# the TFTP server.
|
|
#
|
|
# non-zero = profile from TFTP server is encrypted with this
|
|
# key using the RC4 encryption algorithm.
|
|
#
|
|
# Note: The cfgfmt.exe program will automatically encrypt the binary
|
|
# file when this parameter value is non-zero.
|
|
|
|
EncryptKey:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: EncryptKeyEx
|
|
# Access Code: N/A
|
|
# Value Type: Hexadecimal character string (64 Hex characters maximum)
|
|
#
|
|
# Description: Stronger encryption key that ATA will use to decrypt its
|
|
# configuration profile. When this parameter is set to non-zero
|
|
# value, ATA will ignore EncryptKey parameter, and use this
|
|
# parameter instead. ATA will also look for ata<mac>.x file
|
|
# instead of ata<mac> file for its configuration profile.
|
|
#
|
|
# Options: *0 = EncryptKey parameter value is used, and ATA will look
|
|
# for ata<mac> file.
|
|
#
|
|
# non-zero = profile from TFTP server is encrypted with this
|
|
# key using the stronger RC4 encryption algorithm.
|
|
# This profile is ata<mac>.x.
|
|
#
|
|
# Note: The cfgfmt.exe (version 2.1) program will generate
|
|
# ata<mac>.x file in addition to ata<mac> file if this
|
|
# parameter is specified.
|
|
|
|
#EncryptKeyEx:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: ToConfig (Not used for SCCP)
|
|
# Access Code: 80001
|
|
# Value Type: Boolean
|
|
#
|
|
# Description: Indicate whether ATA has a valid operating configuration
|
|
#
|
|
# Options: *1 = ATA is fresh from the factory and it has no valid
|
|
# operating configuration
|
|
# 0 = ATA has a valid operating configuration
|
|
#
|
|
# Note: The parameter value should be set to 0 once the ATA has a
|
|
# valid operating configuration to prevent unnecessary contacts
|
|
# with the TFTP server, if it is enabled.
|
|
|
|
ToConfig:0
|
|
|
|
# ====================== Firmware Upgrade Parameters ==========================
|
|
# -----------------------------------------------------------------------------
|
|
# Parameters: upgradecode (Not used for SCCP unless for cross protocol)
|
|
#
|
|
# Access Code: N/A
|
|
#
|
|
# Description: Special parameter to provide information on how to upgrade
|
|
# firmware code or language image. The upgrade parameter values
|
|
# should be derived from the corresponding syntax below.
|
|
#
|
|
# Syntax: Upgradecode:3,0x301,0x0400,0x0200,tftp_ip_addr,69,image_id,image_filename
|
|
# Upgradelang:3,0x301,0x0400,0x0200,tftp_ip_addr,69,image_id,language_filename
|
|
#
|
|
# Options: tftp_ip_addr
|
|
# - TFTP server IP address where the image_filename or
|
|
# language_filename is located
|
|
#
|
|
# image_id
|
|
# - A unique 32-bit integer value different from upgrade to
|
|
# upgrade. A simple way to derive this 32-bit integer value
|
|
# is to use the build date on the image file name and
|
|
# prepending it with "0x" (e.g. if the image_filename is
|
|
# ata18x-v2-15-ms-021115a, then the build date is 021115a
|
|
# and image_id is 0x021115a)
|
|
#
|
|
# image_filename
|
|
# - Firmware upgrade image file name. The file name has the
|
|
# following syntax:
|
|
#
|
|
# ata18x-v{M}-{N}-ms-{yymmdd}{a-f}.{ext}
|
|
#
|
|
# M - Major version number
|
|
# N - Minor version number
|
|
# (always expressed as 2 digits)
|
|
# yymmdd - 2 digit year, 2 digit month, 2 digit day
|
|
# a-f - Build letter: a, b, c, d, e or f
|
|
# ext - File extension name ".zup" or ".kxz"
|
|
# NOTE: The file extension MUST be ".kxz" to
|
|
# upgrade from version 2.11 and below,
|
|
# and can be ".zup" for upgrading from
|
|
# version 2.12 and up for the ATA186,
|
|
# but it MUST be ".zup" for upgrading
|
|
# an ATA188.
|
|
#
|
|
# language_filename
|
|
# - Language upgrade image file name. The file name has the
|
|
# following syntax:
|
|
#
|
|
# ata18x-v{M}-{N}-ms-{yymmdd}{a-f}-elang.kup
|
|
#
|
|
#
|
|
# Example for Upgrading Software
|
|
# ------------------------------
|
|
# upgradecode:3,0x301,0x0400,0x0200,192.168.2.170,69,0x020514a,ata186-v2-14-ms-020514a.zup
|
|
#
|
|
# NOTE: The default values listed below will not trigger any upgrade.
|
|
|
|
upgradecode:0,0x301,0x0400,0x0200,0.0.0.0,69,0,none
|
|
|
|
# ===================== Network Configuration Parameters ======================
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: Dhcp
|
|
# IVR Code: 20
|
|
# Value Type: Boolean
|
|
#
|
|
# Description: Enable or disable use of DHCP server for network settings
|
|
#
|
|
# Options: *1 = Use DHCP to obtain IP, route, netmask, DNS, NTP, TFTP, etc.
|
|
# 0 = Don't use DHCP, instead use hard coded parameter values for
|
|
# IP, route, netmask, DNS, NTP, TFTP, etc.
|
|
|
|
dhcp:1
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameters: staticIp
|
|
# staticRoute
|
|
# staticSubNetMask
|
|
#
|
|
# Access Code: 1 StaticIp
|
|
# 2 StaticRoute
|
|
# 10 StaticNetMask
|
|
#
|
|
# Value Type: IP address
|
|
#
|
|
# Description: If Dhcp parameter is set to 0, use these parameters to
|
|
# assign a static IP address, route IP address, and subnet mask
|
|
#
|
|
|
|
StaticIp:0
|
|
StaticRoute:0
|
|
StaticNetMask:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameters: DNS1IP
|
|
# DNS2IP
|
|
#
|
|
# Access Code: 916 DNS1IP (Primary DNS Server)
|
|
# 917 DNS2IP (Secondary DNS Server)
|
|
#
|
|
# Value Type: IP address
|
|
#
|
|
# Description: Primary and secondary DNS server IP addresses
|
|
#
|
|
# If the DHCP server does not provide them or "Dhcp" parameter
|
|
# is set to 0, you must provide at least the primary DNS server
|
|
# IP address; otherwise, domain names cannot be resolved.
|
|
|
|
DNS1IP:0.0.0.0
|
|
DNS2IP:0.0.0.0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: VLANSetting
|
|
# Access Code: 324
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: Control various VLAN settings
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0-2 Specify CoS bit value (802.1P priority) for Signaling
|
|
# IP packets
|
|
# 3-5 Specify CoS bit value (802.1P priority) for Voice
|
|
# IP packets
|
|
# 6-17 RESERVED
|
|
# 18-29 Specify static 802.1Q VLAN ID
|
|
# 30-31 RESERVED
|
|
|
|
VLANSetting:0x0000002b
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: CA0OrCM0 (old, change to CallManager0)
|
|
# CA1orCM1 (old, change to CallManager1)
|
|
#
|
|
# Access code: 5 CA0OrCM0 (Primary Call Manager)
|
|
# 6 CA1OrCM1 (Secondary Call Manager)
|
|
#
|
|
# Value Type: Alphanumeric string (31 characters maximum)
|
|
#
|
|
# Description: Primary and secondary CallManager IP addresses or URLs.
|
|
#
|
|
# The parameter value can be an IP address with or without a port
|
|
# parameter such as 123.123.110.45 or 123.123.110.45:2728, and it
|
|
# can also be a URL such as cs.cisco.com:2727.
|
|
#
|
|
#
|
|
# Syntax: <IP_address | URL>[:<Port>]
|
|
|
|
CA0orCM0:0
|
|
CA1orCM1:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: CA0UID (Not used for SCCP)
|
|
# CA1UID
|
|
#
|
|
# Access Code: 3 CA0UID (Primary Call Agent ID String)
|
|
# 13 CA1UID (Secondary Call Agent ID String)
|
|
#
|
|
# Value Type: Alphanumeric string (31 characters maximum)
|
|
#
|
|
# Description: Primary and secondary Call Agent User ID strings
|
|
|
|
CA0UID:0
|
|
CA1UID:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameters: EPID0orSID0
|
|
# EPID1orSID1
|
|
#
|
|
# Access Code: 46 EPID0orSID0 (Line 1 ID)
|
|
# 47 EPID1orSID1 (Line 2 ID)
|
|
#
|
|
# Value Type: Alphanumeric string (51 characters maximum)
|
|
#
|
|
# Description: Enable/Disable Line 1 and 2 FXS ports and CallManager
|
|
# registrations
|
|
# 0 - FXS port is disabled and no CallManager registration will
|
|
# be attempted
|
|
# *. - FXS port is enabled and CallManager registration will be
|
|
# attempted
|
|
#
|
|
|
|
EPID0orSID0:.
|
|
EPID1orSID1:.
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: PrfCodec (Not used for SCCP)
|
|
# Access Code: 36
|
|
# Value Type: Integer (0 - 3)
|
|
# Description: Preferred audio codec.
|
|
#
|
|
# The ATA's preferred codec is used only in the case when the
|
|
# Call Agent does not provide a list of preferred codecs in the
|
|
# Local Connection Options 'a' parameter and the remote party
|
|
# does not include a codec preference in its SDP.
|
|
#
|
|
# Options: 0 = G.723.1 (can be selected only if LBRCodec is set to 0)
|
|
# 1 = G.711a
|
|
# 2 = G.711u
|
|
# *3 = G.729a (can be selected only if LBRCodec is set to 3)
|
|
|
|
PrfCodec:1
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: LBRCodec
|
|
# Access Code: 300
|
|
# Value Type: Integer (0 or 3)
|
|
# Description: Low bit rate codec that can be used during codec negotiation.
|
|
#
|
|
# Options: 0 = Select g723.1 as the low bit rate codec
|
|
# 3 = Select g729 as the low bit rate codec
|
|
#
|
|
|
|
LBRCodec:3
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: MediaPort
|
|
# Access Code: 202
|
|
# Value Type: Integer (1 - 65535)
|
|
# Description: Base port for receiving RTP media.
|
|
# Note: A value of 0 sets the default port to 16384.
|
|
|
|
MediaPort:16384
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: Domain
|
|
# Access Code: 931
|
|
# Value Type: Alphanumeric string (31 characters maximum)
|
|
#
|
|
# Description: Specifies the domain name used for DNS search if the supplied
|
|
# CallManager URL or TftpURL does not contain a fully qualified
|
|
# domain name. For example, if cml is specified in CA0orCM0 (or
|
|
# by tftp configuration profile) as the CallManager URL, and
|
|
# cisco.com is specified in Domain, then cml@cisco.com will be
|
|
# used for the DNS search
|
|
#
|
|
|
|
Domain:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: PortsSetting
|
|
# Access Code: 73876787
|
|
# Value Type: Integer
|
|
#
|
|
# Description: For setting switch ports
|
|
# Use this parameter to set up Uplink and PC-port speed and duplex
|
|
# Bit0 - bit 3 : PC-port
|
|
# Bit4 - bit 7 : Uplink port
|
|
#
|
|
# Options: Value Description
|
|
# ----- --------------------------------------------------------
|
|
# 0 10M, HALF duplex
|
|
# 1 10M, FULL duplex
|
|
# 2 100M, HALF duplex
|
|
# 3 100M, FULL duplex
|
|
# 4 AUTO detect
|
|
#
|
|
# others invalid
|
|
#
|
|
# Note: 1. If PC-port value is set to higher speed and duplex than that of
|
|
# Uplink port, software will automatically set it to the maximum
|
|
# speed and duplex allowed by the Uplink port.
|
|
# 2. This parameter is only valid on ATA Halmahera. Switch ports can
|
|
# NOT be set on earlier version of ATA 188.
|
|
#
|
|
|
|
PortsSetting:0x00000044
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: L2KeepAlive
|
|
# Access Code: 52525483
|
|
# Value Type: Integer
|
|
#
|
|
# Description: For setting the interval of layer 2 keep alive packet.
|
|
# Default is 0, which means no layer 2 keep alive packets are
|
|
# sent. Set this parameter to non-zero value only if
|
|
# the switch port ATA is connected to require some traffic
|
|
# generated from ATA to keep the port open (you do not
|
|
# normally need this feature). The value represent time
|
|
# in second and valid value are in the range of 0 to
|
|
# 21474836 (behaviour of value outside the range is undefined).
|
|
|
|
L2KeepAlive:0
|
|
|
|
# ======================= Audio Configuration Parameters ======================
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: AudioMode
|
|
# Access Code: 312
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: Control or fine-tune certain audio features.
|
|
#
|
|
# Note: Lower 16-bit controls line 1 and upper 16-bit controls line 2
|
|
#
|
|
# Options: Lines
|
|
# 1 2
|
|
# Bits Bits Values
|
|
# ----- ----- -------------------------------------------------
|
|
# 0 16 G.711 Silence Suppression (Not used for SCCP)
|
|
# 0 = Disable
|
|
# *1 = Enable
|
|
#
|
|
# 1 17 Codec Availability For All Calls
|
|
# *0 = G.711 and selected low bit rate codec
|
|
# 1 = G.711 only
|
|
#
|
|
# 2 18 FAX CED Tone Detection
|
|
# 0 = Disable
|
|
# *1 = Enable
|
|
#
|
|
# 3 19 RESERVED
|
|
#
|
|
# 4-5 20-21 DTMF Transmission Method (Not used for SCCP)
|
|
# 0 = Always in-band
|
|
# 1 = By negotiation
|
|
# 2 = Always out-of-band
|
|
# *3 = Disabled. No DTMF is sent.
|
|
#
|
|
# 6-15 22-31 RESERVED
|
|
|
|
AudioMode:0x00350035
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: NumTxFrames (Not used for SCCP)
|
|
# Access Code: 35
|
|
# Value Type: Integer (1 - 6)
|
|
#
|
|
# Description: Transmit frames per packet.
|
|
#
|
|
# The frame size for each G.711 and G.729 data packet is 10 ms.
|
|
# The frame size for each G.723 data packet is 30 ms.
|
|
#
|
|
# Examples: To obtain 60 ms of G.723 audio, set the value to 2 (=60/30).
|
|
# To obtain 120 ms of G.723 audio, set the value to 4 (=120/30).
|
|
# To obtain 20 ms of G.711 audio, set the value to 2 (=20/10).
|
|
#
|
|
# Note: Cisco recommends using the default value of 2.
|
|
|
|
NumTxFrames:2
|
|
|
|
# ========================= OPERATIONAL PARAMETERS ============================
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: CallerIdMethod
|
|
# Access Code: 316
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: Setup Caller ID signaling method and transmission format.
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0-1 Caller ID (CID) Signaling Standard
|
|
# *0 = Bellcore
|
|
# 1 = DTMF
|
|
# 2 = ETSI
|
|
# 3 = RESERVED
|
|
#
|
|
# ----------------------------------------------------------------
|
|
# (0) Bellcore CID Signaling Bit Definitions
|
|
# ----------------------------------------------------------------
|
|
#
|
|
# 2 RESERVED
|
|
#
|
|
# 3-8 Maximum number of digits in a phone number
|
|
# Range: 1-20 Default: 12
|
|
#
|
|
# 9-14 Maximum number of characters in a name
|
|
# Range: 1-20 Default: 15
|
|
#
|
|
# 15 Send 'O' (out of area) to CID device if number is unknown
|
|
# 0 = Disable
|
|
# *1 = Enable
|
|
#
|
|
# 16 Send 'P' (private) to CID device if number is restricted
|
|
# 0 = Disable
|
|
# *1 = Enable
|
|
#
|
|
# 17-27 RESERVED
|
|
#
|
|
# 28 No Call Waiting Caller ID on line 0
|
|
# 29 No Call Waiting Caller ID on line 1
|
|
#
|
|
# ----------------------------------------------------------------
|
|
# (1) DTMF CID Signaling Bit Definitions
|
|
# ----------------------------------------------------------------
|
|
#
|
|
# 2 RESERVED
|
|
#
|
|
# 3-6 Start digit for known numbers
|
|
# 12 = 'A' 14 = 'C'
|
|
# 13 = 'B' 15 = 'D'
|
|
#
|
|
# 7-10 End digit for known numbers
|
|
# 11 = '#' 14 = 'C'
|
|
# 12 = 'A' 15 = 'D'
|
|
# 13 = 'B'
|
|
#
|
|
# 11 Polarity reversal before and after CID signal
|
|
# 0 = Disable
|
|
# 1 = Enable
|
|
#
|
|
# 12-16 Maximum number of digits in a phone number
|
|
# Range: 1-32 Default: 15
|
|
#
|
|
# 17-19 Start digit for unknown/restricted numbers
|
|
# 4 = 'A' 6 = 'C'
|
|
# 5 = 'B' 7 = 'D'
|
|
#
|
|
# 20-22 End digit for unknown/restricted numbers
|
|
# 3 = '#' 6 = 'C'
|
|
# 4 = 'A' 7 = 'D'
|
|
# 5 = 'B'
|
|
#
|
|
# 23-24 Code to send to CID device if number is unknown
|
|
# 0 = '00'
|
|
# 1 = '0000000000'
|
|
# 2 = '3'
|
|
# 3 = RESERVED. Do not use!
|
|
#
|
|
# 25-26 Code to send to CID device if number is restricted
|
|
# 0 = '10'
|
|
# 1 = '1'
|
|
# 2 = RESERVED. Do not use!
|
|
# 3 = RESERVED. Do not use!
|
|
#
|
|
# 27 RESERVED
|
|
#
|
|
# 28 No Call Waiting Caller ID on line 0
|
|
# 29 No Call Waiting Caller ID on line 1
|
|
#
|
|
# 30-31 DTMF VMWI interface
|
|
# 0 = disable
|
|
# 1 = TeleDanmark MWI, TDK-TS 900 301-5
|
|
# 2-3 = RESERVED
|
|
#
|
|
# ----------------------------------------------------------------
|
|
# (2) ETSI CID Signaling Bit Definitions
|
|
# ----------------------------------------------------------------
|
|
#
|
|
# 2 0 = data transmission prior ringing using RP-AS
|
|
# (Ring Pulse Alerting Signal)
|
|
# 1 = data transmission after 1st ring
|
|
#
|
|
# 3-8 Maximum number of digits in a phone number
|
|
# Range: 1-20 Default: 12
|
|
#
|
|
# 9-14 Maximum number of characters in a name
|
|
# Range: 1-20 Default: 15
|
|
#
|
|
# 15 Send 'O' (out of area) to CID device if number is
|
|
# unknown
|
|
# 0 = Disable
|
|
# *1 = Enable
|
|
#
|
|
# 16 Send 'P' (private) to CID device if number is restricted
|
|
# 0 = Disable
|
|
# *1 = Enable
|
|
#
|
|
# 17-27 RESERVED
|
|
#
|
|
# ---------------------------------------------------------------
|
|
#
|
|
# 28 No Call Waiting Caller ID on line 0
|
|
# 29 No Call Waiting Caller ID on line 1
|
|
#
|
|
# Note: Cisco recommends the following settings:
|
|
#
|
|
# USA = 0x00019e60
|
|
# Sweden = 0x0000ff61 or 0x006aff61
|
|
# Denmark = 0x0000fde1 or 0x033efde1
|
|
# 0x4000fde1 or 0x433efde1 (VMWI enabled)
|
|
# Germany = 0x00019e62
|
|
# Austria = 0x00019e66
|
|
#
|
|
CallerIdMethod:0x00019e60
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: Polarity
|
|
# Access Code: 304
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: Control the FXS ports connect and disconnect polarity
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0 CALLER_CONNECT_POLARITY
|
|
# Polarity to use when ATA is the caller and the call
|
|
# is connected.
|
|
#
|
|
# *0 = Use forward polarity
|
|
# 1 = Use reverse polarity
|
|
#
|
|
# 1 CALLER_DISCONNECT_POLARITY
|
|
# Polarity to use when ATA is the caller and the call
|
|
# is disconnected.
|
|
#
|
|
# *0 = Use forward polarity
|
|
# 1 = Use reverse polarity
|
|
#
|
|
# 2 CALLEE_CONNECT_POLARITY
|
|
# Polarity to use when ATA is the callee and the call
|
|
# is connected.
|
|
#
|
|
# *0 = Use forward polarity
|
|
# 1 = Use reverse polarity
|
|
#
|
|
# 3 CALLEE_DISCONNECT_POLARITY
|
|
# Polarity to use when ATA is the callee and the call
|
|
# is disconnected.
|
|
#
|
|
# *0 = Use forward polarity
|
|
# 1 = Use reverse polarity
|
|
#
|
|
# 4-31 RESERVED
|
|
#
|
|
|
|
Polarity:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: FXSInputLevel
|
|
# Access Code: 370
|
|
# Value Type: Integer (-9 - 2)
|
|
#
|
|
# Description: Input level (A/D) level control of the FXS ports
|
|
|
|
FXSInputLevel:-1
|
|
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: FXSOutputLevel
|
|
# Access Code: 371
|
|
# Value Type: Integer (-9 - 2)
|
|
#
|
|
# Description: Output level (D/A) level control of the FXS ports
|
|
|
|
FXSOutputLevel:-4
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: ConnectMode
|
|
# Access Code: 311
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: SCCP Connection mode related parameters
|
|
#
|
|
# Note: Bits 2 and 8-15 are for FAX passthrough configuration
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0 Call progress tones configuration method
|
|
# *0 = Use CallManager Network Locale Feature
|
|
# (for 3.3(3) CallManager using Locale Installer)
|
|
# 1 = Use ATA Tone parameters
|
|
#
|
|
# 1 RESERVED
|
|
# 2 G.711 Payload Type Number To Use In Fax Passthrough Mode
|
|
# *0 = Use 126 for G.711U and 127 for G.711A
|
|
# 1 = Use 0 for G.711U and 8 for G.711A
|
|
#
|
|
# 3-6 RESERVED
|
|
#
|
|
# 7 Fax Passthrough Redundancy
|
|
# *0 = Disable
|
|
# 1 = Enable
|
|
#
|
|
# 8-12 NSE Payload Type Number - The value is the offset to
|
|
# payload type 96 (valid range 0-23)
|
|
# Default: 4 (= NSE Payload Type 100)
|
|
#
|
|
# 13 FAX Passthrough Codec
|
|
# *0 = G.711U
|
|
# 1 = G.711A
|
|
#
|
|
# 14-15 FAX Passthrough Mode
|
|
# *0 = Enable
|
|
# 1 = Disable
|
|
# Others = RESERVED
|
|
#
|
|
# 16-20 RESERVED
|
|
#
|
|
# 21 G.729 Line Allocation
|
|
# *0 = Enable G.729 on line 0
|
|
# 1 = Enable G.729 on line 1
|
|
#
|
|
# 22-24 RESERVED
|
|
#
|
|
# 25 *0 = use * as the first digit for the pre-call service
|
|
# access code
|
|
# 1 = use # as the first digit for the pre-call service
|
|
# access code
|
|
#
|
|
# bits 26-31 reserved for SCCP configuration
|
|
# 26: Disable Resume softkey
|
|
# *0 to enable Auto Resume Softkey in call waiting state.
|
|
# 1 to disable Auto Resume Softkey in call waiting state for TAPI & soft phone, see detail in CSCdy43324 & CSCea73129
|
|
#
|
|
# 27: Registration mode
|
|
# *0 to diable ATA to register as 7960.
|
|
# 1 to enable ATA to register as 7960. (available in 2.16ms)
|
|
#
|
|
# 28-29 SCCP Mid-call Service Style
|
|
# *0 - ATA Mid-call Style
|
|
# 1 - Bellcore Mid-call Style
|
|
# 2 - VG248 Mid-call Style
|
|
#
|
|
# 30 Cisco IOS Telephony Solution (ITS) Support
|
|
# *0 - Disable ITS support (CallManager support)
|
|
# 1 - Enable ITS support
|
|
#
|
|
# 31 XML configuration profile support
|
|
# 0 - Disable XML configuration profile support (should
|
|
# be used for CallManager version 3.0)
|
|
# *1 - Enable XML configuration profile support (should
|
|
# be used for CallManager version 3.1 or later)
|
|
#
|
|
# Defaults are marked with *.
|
|
|
|
ConnectMode:0x90000400
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: SigTimer
|
|
# Access Code: 318
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: Timeout values to start/stop the certain signaling events
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0-7 CALL WAITING PERIOD (Not used for SCCP)
|
|
# Period between each burst of call waiting tone
|
|
#
|
|
# Range: 0 - 255
|
|
# Factor: 0.1 second increment
|
|
# Note: 0 defaults to 100 (or 10 sec)
|
|
# Default: 100 (0x64 = 10 sec)
|
|
#
|
|
# 8-21 RESERVED
|
|
#
|
|
# 22-25 REORDER DELAY/PSTN-LIKE BEHAVIOR: (SCCP ONLY)
|
|
# In a PSTN-like environment, when far-end disconnects
|
|
# first, there is always a period of silence heard
|
|
# on the line before the reorder (fast busy) tone is
|
|
# played. The same reorder delay can be duplicated
|
|
# on the ATA by configuring these bits in the SigTimer
|
|
# field according to the guildine specified here:
|
|
#
|
|
# Valid Range: 0 - 15
|
|
#
|
|
# Value(s): 0 = wait 4 sec before playing reorder
|
|
# 1 - 14 = wait exactly n number of seconds
|
|
# before starting reorder tone
|
|
# (e.g. value of 2 means wait 2 sec)
|
|
# 15 = never play reorder
|
|
#
|
|
# Default: 0 (wait 4 sec before playing reorder)
|
|
#
|
|
# 26-27 MINIMUM FLASH-HOOK TIME
|
|
# Minimum on-hook time required for flash-hook event
|
|
#
|
|
# *0 = 60 ms 2 = 200 ms
|
|
# 1 = 100 ms 3 = 300 ms
|
|
#
|
|
# 28-31 MAXIMUM FLASH-HOOK TIME
|
|
# Maximum on-hook time allowed for flash-hook event
|
|
#
|
|
# *0 = 1000 ms 8 = 800 ms
|
|
# 1 = 100 ms 9 = 900 ms
|
|
# 2 = 200 ms 10 = 1000 ms
|
|
# 3 = 300 ms 11 = 1100 ms
|
|
# 4 = 400 ms 12 = 1200 ms
|
|
# 5 = 500 ms 13 = 1300 ms
|
|
# 6 = 600 ms 14 = 1400 ms
|
|
# 7 = 700 ms 15 = 1500 ms
|
|
|
|
SigTimer:0x00000064
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: OpFlags
|
|
# Access code: 323
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: Turn ON/OFF various operational features
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0 TFTP Configuration Filename
|
|
# *0 = Use DHCP provided TFTP filename, if available;
|
|
# otherwise, use the internal default TFTP
|
|
# configuration filename
|
|
# 1 = Always use the internal default TFTP
|
|
# configuration filename
|
|
#
|
|
# 1 Network Probing on Power Up
|
|
# 0 = Probe the static network router when power up
|
|
# *1 = Do not perform static network router probing at
|
|
# power up
|
|
#
|
|
# 2 RESERVED
|
|
#
|
|
# 3 DHCP Option 150
|
|
# *0 = Ask for DHCP option 150 in DHCP DISCOVERY message
|
|
# 1 = Do not ask for DHCP option 150 in DHCP DISCOVERY
|
|
# message (some DHCP server will not respond if
|
|
# option 150 is requested)
|
|
#
|
|
# 4 VLAN Network Operation
|
|
# *0 = Do not use the static VLAN ID
|
|
# 1 = Use the static VLAN ID specified in VLANSetting,
|
|
# (see VLANSetting parameter)
|
|
#
|
|
# 5 VLAN Encapsulation
|
|
# *0 = Use VLAN IP encapsulation
|
|
# 1 = Do not use VLAN IP encapsulation, i.e. force
|
|
# turning OFF VLAN tagging
|
|
#
|
|
# 6 Cisco Discovery Protocol (CDP)
|
|
# *0 = Use CDP discovery
|
|
# 1 = Do not perform CDP discovery
|
|
#
|
|
# 7 Web Configuration Access (as of 2.14.020514)
|
|
# *0 = Allow web configuration
|
|
# 1 = Do not allow web configuration
|
|
#
|
|
# 8 TFTP Refresh Access (Not used for SCCP)
|
|
# *0 = Allow force profile update via http://ip/refresh
|
|
# 1 = Do not allow http://ip/refresh
|
|
#
|
|
# 9 Remote Reset Access (Not used for SCCP)
|
|
# *0 = Allow reset of ATA via http://ip/reset
|
|
# 1 = Do not allow reset of ATA via http://ip/reset
|
|
#
|
|
# 10 HOSTNAME of Device
|
|
# *0 = Request device's HOSTNAME from DHCP server
|
|
# 1 = In device's DHCP packets, use device's name
|
|
# as device's HOSTNAME (DHCP option 12)
|
|
#
|
|
# 11 RESERVED
|
|
#
|
|
# 12 RESERVED
|
|
#
|
|
# 13 DNS Servers For Name Resolution
|
|
# *0 = Use statically configured DNS servers, if
|
|
# available; otherwise, use DHCP provided DNS IPs
|
|
# 1 = Use both statically configured (DNS1IP & DNS2IP)
|
|
# and DHCP provided DNS IPs (up to 2)
|
|
# (This configuration bit gives precedence
|
|
# to DHCP provided DNS IPs over statically
|
|
# provided DNS IPs).
|
|
# (Not available in version prior to 2.16)
|
|
#
|
|
# 14 DNS Servers For Name Resolution 2
|
|
# *0 = Use statically configured DNS IPs (DNS1IP &
|
|
# DNS2IP), if available; otherwise, use DHCP
|
|
# provided DNS IPs
|
|
# 1 = Use both statically configured (DNS1IP & DNS2IP)
|
|
# and DHCP provided DNS IPs (up to 2).
|
|
# (This configuration bit gives precedence
|
|
# to statically provided DNS IPs over DHCP
|
|
# provided DNS IPs. When set, it also overwrites
|
|
# configuration bit 13 in OpFlags parameter).
|
|
# (Not available in version prior to 2.16)
|
|
#
|
|
# 15 Disable UDP checksum generation
|
|
# (Not availabe in version prior to 2.16.2 031006)
|
|
# *0 = generate UDP checksum in outgoing UDP packets.
|
|
# 1 = disable generation of of UDP checksum in
|
|
# outgoing UDP packets.
|
|
#
|
|
#
|
|
# 16-27 RESERVED
|
|
#
|
|
# 28-31 If set to 6, FactReset (322873738#)
|
|
# and Local Upgrade (100#) options will be protected
|
|
# by UIPassword also.
|
|
|
|
OpFlags:0x00000002
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: TOS
|
|
# Access Code: 255
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: ToS (Type of Service) bits. This bitmap value specifies the
|
|
# precedence and delay of Audio and Signaling IP packets.
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0-7 ToS Value For Voice Data Packets
|
|
# Range: 0-255 Default: 184
|
|
#
|
|
# 8-15 ToS Value For Signaling Data Packets
|
|
# Range: 0-255 Default: 96
|
|
#
|
|
# 16-31 RESERVED
|
|
|
|
TOS:0x000060B8
|
|
|
|
# ======================== Tone Configuration Parameters ======================
|
|
# -----------------------------------------------------------------------------
|
|
# Parameters: DialTone
|
|
# DialTone2
|
|
# BusyTone
|
|
# ReorderTone
|
|
# RingBackTone
|
|
# CallWaitTone
|
|
# AlertTone
|
|
#
|
|
# Access Code: 920 DialTone
|
|
# 927 DialTone2
|
|
# 921 BusyTone
|
|
# 922 ReorderTone
|
|
# 923 RingBackTone
|
|
# 924 CallWaitTone
|
|
# 925 AlertTone
|
|
#
|
|
# Note: When using ATA with CallManager 3.3(3) that has installed ATA
|
|
# Network Locale option using locale installer, one should specify
|
|
# the call progress tones using the Network Locale option on the
|
|
# CallManager configuration page. Only if the desired locale does
|
|
# not exist, then one should use the ATA tone parameters for
|
|
# configurating call progess tones. To do so, ConnectMode Bit 0 has
|
|
# to be set to 1 to disable CallManager network locale setting.
|
|
# Otherwise, CallManager default configuration (US tone) will
|
|
# overwrite the ATA tone setting.
|
|
#
|
|
# Value Type:
|
|
# Tones can be specified using either Basic Format or Extended Format
|
|
#
|
|
# Basic Format:
|
|
# For all tones:
|
|
# Array of 9 comma-separated short integers
|
|
#
|
|
# Extended Format:
|
|
# (a) For DialTone, DialTone2, BusyTone, RingbackTone, CallWaitTone,
|
|
# AlertTone:
|
|
# Array of 11 comma-separated short integers
|
|
# (b) For ReorderTone:
|
|
# Array of 17 comma-separated short integers
|
|
#
|
|
# NOTE: Basic Format has the same physical number of fields as the
|
|
# extended format, so it is recommended that when specifying in
|
|
# basic format, the unused extended fields are padded with Zeroes
|
|
# (not doing so will not have any detrimental effect but just
|
|
# those unused extended fields may be displayed as random value
|
|
# in the web page interface).
|
|
#
|
|
# Description: Call progress tone specifications
|
|
#
|
|
# Basic Format:
|
|
# NumOfFreqs,Tfreq1,Tfreq2,Tamp1,Tamp2,Steady,OnTime,OffTime,
|
|
# TotalToneTime
|
|
#
|
|
#
|
|
# Options: NumOfFreqs: number of frequencies in the tone (1 or 2)
|
|
#
|
|
# Tfreq1, Tfreq2: the transformed frequencies of the first and
|
|
# second frequencies, respectively. Calculated as follows, where
|
|
# F is the desired frequency in Hz:
|
|
#
|
|
# 32767 * cos(2*pi*F/8000)
|
|
#
|
|
# Tamp1, Tamp2: the transformed amplitude of the first and second # frequencies, respectively. Calculated as follows, where F is
|
|
# desired frequency in Hz, k is the desired volume in dBm, n
|
|
# is the number of frequencies:
|
|
#
|
|
# 32767 * A * sin(2*pi*F/8000)
|
|
# A = 0.5 * 10^((k+10-(n-1)*3)/20)
|
|
#
|
|
#
|
|
# Steady: 0, if a tone with on-off cadence.
|
|
# 1, if a steady tone.
|
|
#
|
|
# OnTime: the length of time the sound is played
|
|
# OffTime: the length of time the silence is played
|
|
# OnTime and OffTime are specified as number of samples with
|
|
# the sampling rate of 8kHz, valid range 1-0xffff
|
|
# For examples, for a lenght of 0.3 seconds, set a value to 2400
|
|
#
|
|
# TotalToneTime: the total length of time the tone plays. If
|
|
# this value is 0, the tone will play until another event stops
|
|
# the tone. For DialTone, DialTone2, BusyTone, ReorderTone, and
|
|
# RingbackTone, the unit is 10 ms (specifying 100 = 1 second).
|
|
# For others, the unit is sample with 8 kHz sampling rate
|
|
# (specifying 8000 = 1 second).
|
|
#
|
|
#
|
|
# Extended Format:
|
|
# a) NumOfFreqs,Tfreq1,Tamp1,Tfreq2,Tamp2,NumOfOnOffPairs,OnTime1,OffTime1,
|
|
# OnTime2,OffTime2,TotalToneTime
|
|
#
|
|
# Options: NumOfFreqs: 100 + number of frequencies in the tone (specify
|
|
# 101 for one frequency, 102 for two frequencies)
|
|
#
|
|
# Tfreq1, Tfreq2: the transformed frequencies of the first and
|
|
# second frequencies, respectively. Calculated as follows, where
|
|
# F is the desired frequency in Hz:
|
|
#
|
|
# 32767 * cos(2*pi*F/8000)
|
|
#
|
|
# Tamp1, Tamp2: the transformed amplitude of the first and second # frequencies, respectively. Calculated as follows, where F is
|
|
# desired frequency in Hz, k is the desired volume in dBm, n
|
|
# is the number of frequencies:
|
|
#
|
|
# 32767 * A * sin(2*pi*F/8000)
|
|
# A = 0.5 * 10^((k+10-(n-1)*3)/20)
|
|
#
|
|
#
|
|
# NumOfOnOffPairs: the number of on-off pairs in the cadence of
|
|
# the tone (0, 1, or 2). For a steady tone, use 0.
|
|
#
|
|
# OnTime1, OnTime2: the length of time the sound is played for
|
|
# the first and second on-off pairs of a cadence, respectively.
|
|
#
|
|
# OffTime1, OffTime2: the length of time the silence is played
|
|
# for the first and second on-off pairs of a cadence,
|
|
# respectively
|
|
#
|
|
# OnTime1, OnTime2, Offtime1, and OffTime2 are specified as
|
|
# number of samples with the sampling rate of 8kHz, valid
|
|
# range 1-0xffff
|
|
# For examples, for a lenght of 300 ms, set a value to 2400
|
|
#
|
|
# TotalToneTime: the total length of time the tone plays. If
|
|
# this value is 0, the tone will play until another event stops
|
|
# the tone. For DialTone, DialTone2, BusyTone, ReorderTone, and
|
|
# RingbackTone, the unit is 10 ms (specifying 100 = 1 second).
|
|
# For others, the unit is sample with 8 kHz sampling rate
|
|
# (specifying 8000 = 1 second).
|
|
#
|
|
#
|
|
# b) Sequential,NumOfFreqs,Tfreq1,Tamp1,Tfreq2,Tamp2,Tfreq3,Tamp3,
|
|
# NumOfOnOffPairs,OnTime1,OffTime1,OnTime2,OffTime2,OnTime2,OffTime3
|
|
# NumOfRepeat,TotalToneTime
|
|
#
|
|
#
|
|
# Options: Sequential: specifies whether multiple frequencies in a tone
|
|
# play simultaneously (100) or sequentially (101). Set to 100
|
|
# for a tone with one frequency. If Sequential is 101,
|
|
# the number of frequencies (NumOfFreqs) has to be the same value
|
|
# as the number of on-off pairs in a cadence (NumOfOnOffPairs)
|
|
#
|
|
# NumOfFreqs: number of frequencies in the tone (1, 2, or 3)
|
|
#
|
|
# Tfreq1, Tfreq2, Tfreq3: the transformed frequencies of the
|
|
# first, second, and third frequencies, respectively. Calculated
|
|
# as follows, where F is the desired frequency in Hz:
|
|
#
|
|
# 32767 * cos(2*pi*F/8000)
|
|
#
|
|
# Tamp1, Tamp2, Tamp3: the transformed amplitude of the first,
|
|
# second, and third frequencies, respectively. Calculated as
|
|
# follows, where F is desired frequency in Hz, k is the desired
|
|
# volume in dBm, n is the number of frequencies (If Sequential
|
|
# is set to 101, n is equal to 1):
|
|
#
|
|
# 32767 * A * sin(2*pi*F/8000)
|
|
# A = 0.5 * 10^((k+10-(n-1)*3)/20)
|
|
#
|
|
#
|
|
# NumOfOnOffPairs: the number of on-off pairs in the cadence of
|
|
# the tone (0, 1, 2, 3). For a steady tone, use 0.
|
|
#
|
|
# OnTime1, OnTime2, OnTime3: the length of time the sound is
|
|
# played for the first, second, and third on-off pairs of a
|
|
# cadence, respectively.
|
|
#
|
|
# OffTime1, OffTime2, OffTime3: the length of time the silence
|
|
# is played for the first, second and third on-off pairs of a
|
|
# cadence, respectively.
|
|
#
|
|
# OnTime1, OnTime2, OnTime3, Offtime1, OffTime2, and OffTime3
|
|
# are specified as number of samples with the sampling rate of
|
|
# 8kHz, valid range 1-0xffff
|
|
# For examples, for a lenght of 300 ms, set a value to 2400
|
|
#
|
|
# NumOfRepeats: number of times that the first on-off pair of
|
|
# the cadence (specified by OnTime1, OffTime1) repeats before
|
|
# the second on-off pair (specified by OnTime2, OffTime2) plays
|
|
#
|
|
# For example, if NumOfRepeats is 2, the first on-off pair will
|
|
# play three times (it will play once and then repeat two times)
|
|
# then the scond on-off pair will play
|
|
#
|
|
# TotalToneTime: the total length of time the tone plays. If
|
|
# this value is 0, the tone will play until another event stops
|
|
# the tone. For DialTone, DialTone2, BusyTone, ReorderTone, and
|
|
# RingbackTone the unit is 10 ms (specifying 100 = 1 second).
|
|
# For others, the unit is sample with 8 kHz sampling rate
|
|
# (specifying 8000 = 1 second).
|
|
#
|
|
#
|
|
|
|
DialTone:2,31538,30831,1380,1740,1,0,0,1000,0,0
|
|
DialTone2:2,29780,30743,1252,1384,1,0,0,1000,0,0
|
|
BusyTone:2,30467,28959,1191,1513,0,4000,4000,0,0,0
|
|
ReorderTone:2,30467,28959,1191,1513,0,2000,2000,0,0,0,0,0,0,0,0,0
|
|
RingBackTone:2,30831,30467,1943,2111,0,16000,32000,0,0,0
|
|
CallWaitTone:1,30831,0,5493,0,0,2400,2400,4800,0,0
|
|
AlertTone:1,30467,0,5970,0,0,480,480,1920,0,0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: RingCadence (Not used for SCCP)
|
|
# Access Code: 929
|
|
# Value Type: Array of three comma-separated, short integers
|
|
# Description: Control phone ring characteristic.
|
|
#
|
|
# Note: Cisco recommends the following settings:
|
|
#
|
|
# USA = 2,4,25
|
|
# Sweden = 1,5,25
|
|
|
|
RingCadence:2,4,25
|
|
|
|
# ============================ Diagnostic Parameters ==========================
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: NPrintf
|
|
# Access Code: 81
|
|
# Value Type: Extended IP
|
|
#
|
|
# Description: FOR DIANOSTIC USE. Use this parameter to specify the IP
|
|
# address and port number where the Cisco 7905 will send its
|
|
# debug output information.
|
|
#
|
|
# The program "prserv.exe", which is included in all software
|
|
# upgrade package, is needed to capture the debug information.
|
|
# For example, to send message to the host at 192.168.2.170 and
|
|
# port number 9001, execute "prserv 9001" on a PC and specify
|
|
# "192.168.2.170.9001" as the value of this parameter.
|
|
#
|
|
# Syntax: <HOST_IP>.<HOST_PORT>
|
|
|
|
NPrintf:0
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: TraceFlags
|
|
# Access Code: 313
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: FOR DIAGNOSTIC USE. Use this parameter to turn ON specific a
|
|
# specific trace.
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0-6 RESERVED
|
|
# 7 0: simplified SCCP message log
|
|
# 1: detailed SCCP message log
|
|
# 8-31 RESERVED
|
|
|
|
TraceFlags:0x00000000
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: SyslogIP
|
|
# Access Code: 7975640
|
|
# Value Type: Extended IP
|
|
#
|
|
# Description: FOR DIANOSTIC USE. Use this parameter to specify the IP
|
|
# address and port number where the Cisco ATA 186/188 will send
|
|
# its syslog output information.
|
|
#
|
|
# The program "prserv.exe", which is included in all software
|
|
# upgrade package, is needed to capture the syslog information.
|
|
# For example, to send message to the host at 192.168.2.170 and
|
|
# port number 514, execute "prserv 514" on a PC and specify
|
|
# "192.168.2.170.514" as the value of this parameter.
|
|
#
|
|
# Syntax: <HOST_IP>.<HOST_PORT>
|
|
|
|
SyslogIP:0.0.0.0.514
|
|
|
|
# -----------------------------------------------------------------------------
|
|
# Parameter: SyslogCtrl
|
|
# Access Code: 7975641
|
|
# Value Type: Bitmap
|
|
#
|
|
# Description: FOR DIAGNOSTIC USE.
|
|
# Use this parameter to turn ON specific syslog traces. All
|
|
# traces are sent to the syslog server specified in 'SyslogIP'.
|
|
#
|
|
#
|
|
# Options: Bit Values
|
|
# ----- --------------------------------------------------------
|
|
# 0 ARP messages
|
|
# 1 DHCP messages
|
|
# 2 TFTP messages
|
|
# 3 ATA configuration update messages
|
|
# 4 system reboot messages
|
|
#
|
|
# 9 ATA event messages
|
|
# 10 FAX event messages
|
|
#
|
|
# 16 RTP STATISTICS messages
|
|
#
|
|
# others RESERVED
|
|
|
|
SyslogCtrl:0x00000000
|
|
|